10 - Test endstop/movimenti

______________________________________
Cosa serve ora?

• Elettronica                      
• Endstop                          
• Cavi                                
• Parti Plastiche Endstop    
• Fascette Piccole              

Modificare il Firmware (marlin) disponibile in varie opzioni preconfigurato qui
nella parte denominata Mechanical setting---> in Configuration.h.


- 3 Endstop meccanici
- 2 Endstop meccanici (asse X e Y) 1 ottico asse Z

-----------------------

- 3 Endstop meccanici

//===========================================================================

//=============================Mechanical Settings===========================

//===========================================================================



// Uncomment the following line to enable CoreXY kinematics

// #define COREXY



// corse Endstop Settings

//#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors



#ifndef ENDSTOPPULLUPS

  // fine Enstop settings: Individual Pullups. will be ignord if ENDSTOPPULLUPS is defined

  #define ENDSTOPPULLUP_XMAX

  #define ENDSTOPPULLUP_YMAX

  #define ENDSTOPPULLUP_ZMAX

  #define ENDSTOPPULLUP_XMIN

  #define ENDSTOPPULLUP_YMIN

  #define ENDSTOPPULLUP_ZMIN

#endif



#ifdef ENDSTOPPULLUPS

  //#define ENDSTOPPULLUP_XMAX

  //#define ENDSTOPPULLUP_YMAX

  //#define ENDSTOPPULLUP_ZMAX

  #define ENDSTOPPULLUP_XMIN

  #define ENDSTOPPULLUP_YMIN

  #define ENDSTOPPULLUP_ZMIN

#endif



// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.

const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 

const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 

const bool Z_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 

//#define DISABLE_MAX_ENDSTOPS



// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

#define X_ENABLE_ON 0

#define Y_ENABLE_ON 0

#define Z_ENABLE_ON 0

#define E_ENABLE_ON 0 // For all extruders



// Disables axis when it's not being used.

#define DISABLE_X false

#define DISABLE_Y false

#define DISABLE_Z true

#define DISABLE_E false // For all extruders



#define INVERT_X_DIR true    // for Mendel set to false, for Orca set to true

#define INVERT_Y_DIR false    // for Mendel set to true, for Orca set to false

#define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true

#define INVERT_E0_DIR true   // for direct drive extruder v9 set to true, for geared extruder set to false

#define INVERT_E1_DIR false    // for direct drive extruder v9 set to true, for geared extruder set to false

#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false



// ENDSTOP SETTINGS:

// Sets direction of endstops when homing; 1=MAX, -1=MIN

#define X_HOME_DIR -1

#define Y_HOME_DIR -1

#define Z_HOME_DIR -1



#define min_software_endstops false //If true, axis won't move to coordinates less than HOME_POS.

#define max_software_endstops true  //If true, axis won't move to coordinates greater than the defined lengths below.

-----------------------

- 2 Endstop meccanici (asse X e Y) 1 ottico asse Z

//===========================================================================

//=============================Mechanical Settings===========================

//===========================================================================



// Uncomment the following line to enable CoreXY kinematics

// #define COREXY



// corse Endstop Settings

//#define ENDSTOPPULLUPS // Comment this out (using // at the start of the line) to disable the endstop pullup resistors



#ifndef ENDSTOPPULLUPS

  // fine Enstop settings: Individual Pullups. will be ignord if ENDSTOPPULLUPS is defined

  #define ENDSTOPPULLUP_XMAX

  #define ENDSTOPPULLUP_YMAX

//  #define ENDSTOPPULLUP_ZMAX

  #define ENDSTOPPULLUP_XMIN

  #define ENDSTOPPULLUP_YMIN

 // #define ENDSTOPPULLUP_ZMIN

#endif



#ifdef ENDSTOPPULLUPS

  //#define ENDSTOPPULLUP_XMAX

  //#define ENDSTOPPULLUP_YMAX

  //#define ENDSTOPPULLUP_ZMAX

  #define ENDSTOPPULLUP_XMIN

  #define ENDSTOPPULLUP_YMIN

 // #define ENDSTOPPULLUP_ZMIN

#endif



// The pullups are needed if you directly connect a mechanical endswitch between the signal and ground pins.

const bool X_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 

const bool Y_ENDSTOPS_INVERTING = true; // set to true to invert the logic of the endstops. 

const bool Z_ENDSTOPS_INVERTING = false; // set to true to invert the logic of the endstops. 

//#define DISABLE_MAX_ENDSTOPS



// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1

#define X_ENABLE_ON 0

#define Y_ENABLE_ON 0

#define Z_ENABLE_ON 0

#define E_ENABLE_ON 0 // For all extruders



// Disables axis when it's not being used.

#define DISABLE_X false

#define DISABLE_Y false

#define DISABLE_Z true

#define DISABLE_E false // For all extruders



#define INVERT_X_DIR true    // for Mendel set to false, for Orca set to true

#define INVERT_Y_DIR true    // for Mendel set to true, for Orca set to false

#define INVERT_Z_DIR true     // for Mendel set to false, for Orca set to true

#define INVERT_E0_DIR true   // for direct drive extruder v9 set to true, for geared extruder set to false

#define INVERT_E1_DIR false    // for direct drive extruder v9 set to true, for geared extruder set to false

#define INVERT_E2_DIR false   // for direct drive extruder v9 set to true, for geared extruder set to false



// ENDSTOP SETTINGS:

// Sets direction of endstops when homing; 1=MAX, -1=MIN

#define X_HOME_DIR -1

#define Y_HOME_DIR -1

#define Z_HOME_DIR -1



#define min_software_endstops false //If true, axis won't move to coordinates less than HOME_POS.

#define max_software_endstops true  //If true, axis won't move to coordinates greater than the defined lengths below.

______________________________________